51 Mercury Custom Light LensesPerry SR from Sieberts Custom Paint and Body was working on a Mercury and wanted the grille to be just right. He decided on a grille bar made from oval…
51 Mercury - Buick Stainless ModificationPerry SR from Sieberts Custom Paint and Body was working on a Mercury and really liked some stainless side trim from a Buick and thought it would look just…
64 Charger Concept Car Stainless GrilleA local friend that is in to Mopars and works on them too, wanted some stainless trim pieces from another application, cut and pasted together as well as bent…
Stainless Tubing BeaderA custom designed and built tubing beader for stainless tube used to make the Push N Putt Golf accessory. Snippet from Jerry's Letter of Recommendation (see…
Aluminum Bed CoverA customer of Sieberts Body Shop had talked to me about building an aluminum bed cover for his truck, because he had an extra deep custom toolbox in the front…
40 Ford Signature EngravingPJ was building a 1940 Ford for a customer in rememberance of a family member Kenny Gritz. They wanted to put his signature on the motor, so he had me do a…
41 Lincoln Hinge Pins and KnobsMaking some quick stainless hinge pins for a 1941 Lincoln Continental. PJ from Sieberts Custom Paint & Body was working on the Lincoln, and he wanted some…
Bobcat Root Ripper BucketI was contacted by a local farmer who wanted a bucker for his bobcat similar to regular "Stump Buckets" although he wanted it to have a smaller opening and fit…
1932 Ford Quarter ScaleA customer was building a 1/4 scale 1932 Ford and wanted me to build a chassis for it. He did the final welding of the crossmembers to be sure that it fit the…
32 Ford AC Vent BezelsPj was building a 1932 ford and had me cutout some aluminum bezels so he could make some custom AC vents for the dash. I cut them out, and he cleaned them up…
Fire Pit GrateI was asked by a local customer if i could make a large firepit grate with a hinged side and get it done ASAP for a gift. Sure, why not.
51 Mercury Wiper EscutcheonsPerry SR's Mercury had custom wipers installed, but the trim pieces that were available, were not what he wanted. I was helping him look for some, and then…
Aluminum Fuel Tank ModificationPerry SR was putting a gas tank in a customers truck and wanted the filler to be exactly in a certain spot because of the wooden bed floor and billet filler…
Bumper Mount Back Up SensorsCustomer wanted to mount some back up sensors on the rear bumper of a Model A pickup. I machined some aluminum housings to make them a little nicer than the…
Rotary Welding PositionerI got tired of welding in circles by hand and cleaning up the mess that sometimes was made, so i decided to build a Rotary Welding Positioner with a 3 jaw…
English Wheel Adjuster PrototypeAn English Wheel Adjuster that was on my to do list and PJ needed one, so we bumped it up on the list and made a working prototype for him. Will become a…
Golf Cart Aluminum Gas TankWhy such a nice gas tank for a golf cart? Because it has a 3 wheeler motor in it with a clutchless 5 speed, can do 50mph and I like cool!
33 34 Frame Stubs1933-34 Ford Rear frame stubs at request from a customer who was not satisfied with aftermarket quality of other parts.
CNC Plasma Cutting JobsShowing the capabilities of our machine and misc completed parts/jobs. Contact me for a quote or to help you with your idea.
CNC Rotary Tube Cutting PrototypeBuilding a CNC Rotary Tube Cutting attachment for the CNC Plasma / Scribe table, and some test cuts. More to come once all the bugs are worked out and its…
Car Show TrophiesSome trophies that I made for the local Bradshaw Days Car Show 2014. The CNC Plasma/Scribe table does a good job of making nice looking trophies relatively…
Gussets for 4 to 8 inch tubeA local business needed 200 gussets cut from 3/16" steel, and having me cut them on the CNC table beat out the other option of cutting them all on the bandsaw…
Customer Submitted PhotosPhotos sent in by our satisfied customers. Send yours in to get it added! Include info about your shop/project and we will add it for everyone else to see!
Customer ProjectsCustom projects to meet the needs of our customers.
51 Mercury Custom Light LensesPerry SR from Sieberts Custom Paint and Body was working on a Mercury and wanted the grille to be just right. He decided on a grille bar made from oval…
51 Mercury - Buick Stainless ModificationPerry SR from Sieberts Custom Paint and Body was working on a Mercury and really liked some stainless side trim from a Buick and thought it would look just…
64 Charger Concept Car Stainless GrilleA local friend that is in to Mopars and works on them too, wanted some stainless trim pieces from another application, cut and pasted together as well as bent…
Stainless Tubing BeaderA custom designed and built tubing beader for stainless tube used to make the Push N Putt Golf accessory. Snippet from Jerry's Letter of Recommendation (see…
Aluminum Bed CoverA customer of Sieberts Body Shop had talked to me about building an aluminum bed cover for his truck, because he had an extra deep custom toolbox in the front…
40 Ford Signature EngravingPJ was building a 1940 Ford for a customer in rememberance of a family member Kenny Gritz. They wanted to put his signature on the motor, so he had me do a…
41 Lincoln Hinge Pins and KnobsMaking some quick stainless hinge pins for a 1941 Lincoln Continental. PJ from Sieberts Custom Paint & Body was working on the Lincoln, and he wanted some…
Bobcat Root Ripper BucketI was contacted by a local farmer who wanted a bucker for his bobcat similar to regular "Stump Buckets" although he wanted it to have a smaller opening and fit…
1932 Ford Quarter ScaleA customer was building a 1/4 scale 1932 Ford and wanted me to build a chassis for it. He did the final welding of the crossmembers to be sure that it fit the…
32 Ford AC Vent BezelsPj was building a 1932 ford and had me cutout some aluminum bezels so he could make some custom AC vents for the dash. I cut them out, and he cleaned them up…
Fire Pit GrateI was asked by a local customer if i could make a large firepit grate with a hinged side and get it done ASAP for a gift. Sure, why not.
Figure 8 Race TrophiesLocal Figure racing group NeFigure8n wanted some trophies made.
51 Mercury Wiper EscutcheonsPerry SR's Mercury had custom wipers installed, but the trim pieces that were available, were not what he wanted. I was helping him look for some, and then…
Aluminum Fuel Tank ModificationPerry SR was putting a gas tank in a customers truck and wanted the filler to be exactly in a certain spot because of the wooden bed floor and billet filler…
Bumper Mount Back Up SensorsCustomer wanted to mount some back up sensors on the rear bumper of a Model A pickup. I machined some aluminum housings to make them a little nicer than the…
/thumbs/2014-08-08 20.27.32.jpg)
Shop ProjectsProjects done for our shop, for future products or for fun.
Rotary Welding PositionerI got tired of welding in circles by hand and cleaning up the mess that sometimes was made, so i decided to build a Rotary Welding Positioner with a 3 jaw…
English Wheel Adjuster PrototypeAn English Wheel Adjuster that was on my to do list and PJ needed one, so we bumped it up on the list and made a working prototype for him. Will become a…
Golf Cart Aluminum Gas TankWhy such a nice gas tank for a golf cart? Because it has a 3 wheeler motor in it with a clutchless 5 speed, can do 50mph and I like cool!
ProductsPhotos pertaining to our currently manufactured products.
Shrinking Discs and Sheetmetal RepairRust repair, dent repair, shrinking disc usage/tips and anyhthing else pertaining to autmotive sheetmetal.
Yamaha Banshee Extended SwingarmsSome various pictures of our swingarms showing old versions, new improved versions and a few custom color orders.
Yamaha Banshee Footpeg ExtensionsSome pics of our Yamaha Banshee Footpeg Extensions.
33 34 Frame Stubs1933-34 Ford Rear frame stubs at request from a customer who was not satisfied with aftermarket quality of other parts.
CNC Plasma Cutting JobsShowing the capabilities of our machine and misc completed parts/jobs. Contact me for a quote or to help you with your idea.
CNC Rotary Tube Cutting PrototypeBuilding a CNC Rotary Tube Cutting attachment for the CNC Plasma / Scribe table, and some test cuts. More to come once all the bugs are worked out and its…
Car Show TrophiesSome trophies that I made for the local Bradshaw Days Car Show 2014. The CNC Plasma/Scribe table does a good job of making nice looking trophies relatively…
Gussets for 4 to 8 inch tubeA local business needed 200 gussets cut from 3/16" steel, and having me cut them on the CNC table beat out the other option of cutting them all on the bandsaw…
Customer Submitted PhotosPhotos sent in by our satisfied customers. Send yours in to get it added! Include info about your shop/project and we will add it for everyone else to see!
